แบบฝึกหัดที่ 18





#include <SoftwareSerial.h>
#include <DHT11.h>
//=============================================
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
//LiquidCrystal_I2C lcd(0x27, 16, 2);
LiquidCrystal_I2C lcd(0x3F, 16, 2);
SoftwareSerial ArduinoSerial(3, 2); // RX, TX
//=============================================
int SW_ON = 4,SW_OFF = 5,pin=6;//กำหนดขา INPUT
int Sun = 9,CSun = 0,Relay1 = 12, Relay2 = 11; //กำหนดขา OUTPUT
int ATL = A0,ATH = A1;//กำหนดขา Analog
int VTL1 = 0,VTH1 = 0,TL = 0,TH =0,VRHL = 50,VRHH = 80;
DHT11 dht11(pin);
//=============================================
void setup()
{
  lcd.begin();
  Serial.begin(115200);
  ArduinoSerial.begin(4800);
  while (!Serial){
    ;
    }
  //=====================================================
  lcd.setCursor(0, 0);lcd.print("Elec Pattayatech");
  lcd.setCursor(0, 1);lcd.print("Smart Farm 2016 ");
  delay(5000);
  //====================================================
  pinMode(Relay1, OUTPUT);pinMode(Relay2, OUTPUT); 
  pinMode(SW_ON, INPUT); pinMode(SW_OFF, INPUT); pinMode(Sun, INPUT);
  digitalWrite(Relay1, HIGH);digitalWrite(Relay2, HIGH);
  lcd.setCursor(0, 0);lcd.print("                ");
  lcd.setCursor(0, 1);lcd.print("                ");
}
//=============================================================
void loop()
{
  while (ArduinoSerial.available() > 0) {
  float val = ArduinoSerial.parseFloat();
  if (ArduinoSerial.read() == '\n') {
  if (val == 10) {
  digitalWrite(13, 1);
  } else if (val == 11) {
  digitalWrite(13, 0);
  }
  Serial.println(val);
  }
  }
  delay(100);
  //========ปรับค่าอุณหภูมิอ้งอิง====================================
  CSun = digitalRead(Sun);
  int err;
  float temp, humi;
  if((err=dht11.read(humi, temp))==0)
  {
  VTL1 = analogRead(ATL);
  VTH1 = analogRead(ATH);
  TL = map(VTL1,0,1023,10,30);
  TH = map(VTH1,0,1023,25,45);
  Serial.print("TL :");Serial.print(TL);Serial.println("*C");
  Serial.print("TH :");Serial.print(TH);Serial.println("*C");
  //===========================================================
    int Stemp =(int)(temp);int Shumi=(int)(humi);//ตัดทศนิยม
    Serial.print("temp :");Serial.print(Stemp);Serial.println("*C");
    Serial.print("humidity :");Serial.print(Shumi);Serial.println("%");
    Serial.print("SUN :");Serial.println(CSun);//Serial.println();
    //===================================================
    lcd.setCursor(0, 0);lcd.print("TL:");lcd.print(TL);
    lcd.setCursor(6, 0);lcd.print("TH:");lcd.print(TH);
    lcd.setCursor(12, 0);lcd.print("S1:");lcd.print(!CSun);
    lcd.setCursor(0, 1);lcd.print("TN:");lcd.print(Stemp);
    lcd.setCursor(6, 1);lcd.print("RH:");lcd.print(Shumi);
    lcd.setCursor(12, 1);lcd.print("P1:0");lcd.print(Shumi);
    delay(1000);
    //===================================================
   //=======ควบคุมอุณหภูมิ===========================
   if(temp < TL && temp < TH ){
        digitalWrite(Relay1, HIGH);//ปั๊มน้ำหยุดทำงาน
        lcd.setCursor(12, 1);lcd.print("P1:0");
        delay(100);
        digitalWrite(Relay2, LOW);//หลอดไฟทำงาน
        lcd.setCursor(12, 0);lcd.print("L1:1");
        delay(60000);//หน่วงเวลา 1 นาที
      }else if(temp > TL && temp > TH){
        digitalWrite(Relay2, HIGH);//หลอดไฟไม่ทำงาน
        lcd.setCursor(12, 0);lcd.print("L1:0");
        delay(100);
        digitalWrite(Relay1, LOW);//ปั๊มน้ำทำงาน
        lcd.setCursor(12, 1);lcd.print("P1:1");
        delay(60000);//หน่วงเวลา 1 นาที
      }else if(temp > TL && temp < TH){
       //=======ควบคุมความชื้น===========================
      if(humi < VRHL && humi < VRHH){
        digitalWrite(Relay2, HIGH);//หลอดไฟไม่ทำงาน
        lcd.setCursor(12, 0);lcd.print("L1:0");
        delay(100);
        digitalWrite(Relay1, LOW);//ปั๊มน้ำทำงาน
        lcd.setCursor(12, 1);lcd.print("P1:1");
        delay(60000);//หน่วงเวลา 1 นาที
      }else if(humi > VRHL && humi > VRHH){
        digitalWrite(Relay1, HIGH);//ปั๊มน้ำหยุดทำงาน
        lcd.setCursor(12, 1);lcd.print("P1:0");
        delay(100);
        digitalWrite(Relay2, LOW);//หลอดไฟทำงาน
        lcd.setCursor(12, 0);lcd.print("L1:1");
        delay(60000);//หน่วงเวลา 1 นาที
      }else if(humi > VRHL && humi < VRHH){
        //delay(1000);
        digitalWrite(Relay1, HIGH);//ปั๊มน้ำหยุดทำงาน
        lcd.setCursor(12, 1);lcd.print("P1:0");
        digitalWrite(Relay2, HIGH);//หลอดไฟไม่ทำงาน
        lcd.setCursor(12, 0);lcd.print("L1:0");
        //หน่วงเวลา 1 นาที     
        }
     //=======ENDควบคุมความชื้น===========================   
        }
     //=======ENDควบคุมอุณหภูมิ===========================
  }
  else
  {
    Serial.println();Serial.print("Error No :");
    Serial.print(err);Serial.println(); 
  }
 delay(DHT11_RETRY_DELAY);
}

ความคิดเห็น

แสดงความคิดเห็น

โพสต์ยอดนิยมจากบล็อกนี้

7 Segment Display Interfacing with PIC Microcontroller

รูปภาพ
7 Segment Display Interfacing with PIC Microcontroller EMBEDDED 12 7 Segment Display Interfacing with PIC Microcontroller This is our 8th tutorial of  Learning PIC microcontrollers using MPLAB and XC8 . We have come up all the way from  installing MPLABX  to using a LCD with PIC MCU. If you are new here, then look at previous tutorials where you can  learn timers ,  blinking LED ,  interfacing LCD  etc.. You can find all our  PIC Tutorials here . In our last tutorial we saw how we can generate  Custom characters with our 16*2 LCD display , now let us equip our self with another type of display module called the  7-segment display and interface it with PIC Microcontroller . Although  16x2 LCD  is much more comfortable than 7-segment display but there are few scenarios where a 7-segment display would come in handier than a LCD display. LCD suffers from the drawback of having low character size and will ...
อ่านเพิ่มเติม

arduino Project (อ้างอิง : https://www.prometec.net/control-acceso-clave/)

รูปภาพ
CONTROL DE ACCESO CON CLAVE ALFANUMERICA Conmutadores de corriente alterna a 220V. Presentar un interruptor inalámbrico de 4 vías. Ver un caso práctico, de cómo conmutar varios dispositivos de 220V. MATERIAL REQUERIDO.    Arduino UNO o equivalente . Teclado matricial 4×4 Un display  LCD, de 16×2  o  LCD 20×4 , I2C. Resistencias  de: 1 x 100 Ohm, 1/4W  para el buzzer 2 x 330 Ohm, 1/4W para los LEDs Un  LED rojo y otro Verde . Una  Protoboard  . Algunos cables de protoboard, preferiblemente  Dupont macho/hembra . Fuente de alimentación externa 5V  Buzzer pasivo SIMULANDO UN ACCESO CON CLAVE AUN LOCAL No es raro que de una forma u otra acabemos encontrandonos con la necesidad de montar un sistema de control que nos permita activar algo, una cerradura por ejemplo, mediante un codigo numerico tecleado en un keypad a modo de clave de control de acceso. Y como estoy seguro...
อ่านเพิ่มเติม

Digital Thermometer using LM35 and PIC Microcontroller

รูปภาพ
Digital Thermometer using LM35 and PIC Microcontroller EMBEDDED By Pankaj Khatri   May 14, 2018 4 Digital Thermometer using LM35 and PIC microcontroller In this tutorial, we are making a  Digital Thermometer using PIC microcontroller and LM35 Temperature Sensor . In this project, we will sense the temperature using LM35 and display it on  16x2 LCD . LM35 Temperature Sensor is accurate and cheaper and doesn’t require any external calibration. The output voltage is proportional to Celsius temperature scale and changes by 10mV per °C. Material Required PicKit 3 LM35 Temperature Sensor 16*2 LCD PIC16F877A IC 40 - Pin IC holder Perf board 20 MHz Crystal OSC Female and Male Bergstick pins 33pf Capacitor - 2Nos, 100uf and 10uf cap. 680 ohm, 220 ohm, 10K and 560ohm Resistor Potentiometer 10k LED of any color 1 Soldering kit IC 7805 12V Adapter Connecting wires Breadboard LM35 Temperature Sensor: LM35 temperature sensor ...
อ่านเพิ่มเติม